Design Tools Trash Automatic Using microcontroller Arduino
Main Article Content
Abstract
Waste is a waste which can not be used again, which could in solid, liquid or gas form. If we hear that a litter box can make the surrounding environment uncomfortable because it causes a foul odor and can also be a source of diseases such as itching, diarrhea, flu, dengue, bacteria and others. This can provide problems where the author can take the initiative to conduct research to be able to design and build a garbage box tool that works automatically by using an ultrasonic sensor HC-SR04 as a detector of an object that is in front of him using a distance of 10 cm which can be adjusted according to the command so that that distance will be able to open the trash box if it exceeds the distance of 10 cm then the sensor will not work, to open the trash box using a micro servo given 10 seconds to open the trash box if it is more than the specified time then the trash box will work to close the trash box where the dfplayer and speakers work to issue sounds that will be determined according to commands such as saying thank you for throwing trash in its place for the control system using an Arduino microcontroller to run a program. the set to work properly. The purpose of building the garbage box tool is so that the community is protected from bacteria that exist on the surface of the garbage box that can cause disease and increase the community to always take care of the surrounding environment.
Article Details
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
References
F. Sarasati and F. Avicenna, “Ministry of health public communication media,” VISIONER J. Researcher. commune. and Information., vol. 3, no. 1, pp. 327–332, 2021.
DE Rizki Pardamean Sinaga, Bambang Widodo, Susilo, Stepanus, “Design of an Automatic Human Body Temperature Measurement System Without Physical Contact With an Arduino Uno-Based Mlx90614 Temperature Sensor in a Disinfectant Room,” J. Ilm., vol. 3, no. September, pp. 1–10, 2020.
PLE Aritonang, EC Bayu, SD K, and J. Prasetyo, “the Prototype of Automatic Smart Trash Clustering Tool,” Snitt, pp. 375–381, 2017.
M. Syaifudin, F. Rofii, and A. Qustoniah, “Design of a Monitoring System for Household Garbage and Street Lighting Based on Wireless Sensor Network (Wsn),” Transmission, vol. 20, no. 4, p. 158, 2019, doi:10.14710/transmisi.20.4.158-166.
D. Ariadi and Tashid, “Prototype of Waste Surface Height Measuring System,” JOISIE J. Inf. syst. Informatics Eng., vol. 2, no. 1, pp. 18–25, 2018.
Helmy Yudhistira Putra and Utomo Budiyanto, “Design of Body Temperature Measurement With Multi Sensors to Prevent the Spread of Covid-19,” J. RESTI (System Engineering and Information Technology), vol. 5, no. 3, pp. 543–549, 2021, doi:10.29207/resti.v5i3.2931.
W. SARI, “Design of Arduino-Based Smart Trash Cans to Support Clean Civilization Program at Universitas Pembangunan Panca Budi Medan,” Kumpul. Scientific Works. Mhs. Fac. science …, 2021, [Online]. Available: http://jurnal.pancabudi.ac.id/index.php/fastek/article/download/1774/1615.
L. Sri, A. Muni, and CD Lestari, “WITH SMARTBIN NOTIFICATION BASED DESIGN WITH NOTIFICATION,” pp. 1–7.
Suherman, Mardeni, Y. Irawan, and Sugiati, "Design of Automatic Trash Can Using Microcontroller and Ultrasonic Sensor With Telegram Notification," Jik, vol. 9, no. 2, pp. 154–160, 2020, [Online]. Available: http://jik.htp.ac.id.
Elsi, Zulhipni Reno Saputra, "Design of a Body Temperature Detection Device With a Contacless Sensor Based on Arduino Uno," Jusikom J. Sist. computer. Musirawas, vol. 6, no. 1, pp. 50–59, 2021, doi:10.32767/jusikom.v6i1.1243.
P. Studi, T. Information, U. Muhammadiyah, and S. Ultrasonic, “NON-TOUCHING HANDSANITIZER DISPENSER,” vol. 6, no. 2, pp. 133–141, 2021.